Hi-Q Accessories

Choose a product below for pricing and ordering information (and pictures and specs, if available):

• Capacitance Hat (CapHat) (Four Lobes)
• Capacitance Hat (CapHat) - Adjustable (Single Lobe)
• Circuit breaker
• Coupler box, Standard
• DPDT control switch
• Ferrite RF Chokes
• Fold-Over Base
• Fold-Over Whip
• Four pin connector
• Giant Quick Disconnects (GQD)
• Insulating Wafers
• Motors
• Mounting Brackets and Systems
• Quick Disconnects (GQD / WQD)
• Reed Switch
• RF Filters (Ferrites)
• Rigidized Military Spring Mount
• Stainless Steel stud for extension rod
• Toroid Cores
• TriPod for portable use
• Whip Base
• Whip Quick Disconnects (WQD)

• Four pin connector
     male/female, $5.00
          

• Circuit breaker
     Four amps, re-settable, $4.00
          

• Coupler Box, Standard
     $125
          

• Extra set of insulating wafers
     $10.00 per set
          

• DPDT control switch
     $7.00 each
          

• Whip Base
  When the whip is cut off you use this to accept the whip with set screws.
     3/8-24 base, brass, silver plated with SS stud, $10.00
          
     3 section with spring base for portable use, $10.00
          

• Stainless Steel stud for extension rod
     8-24 x 1.5", $4.00
          

• Shipping/Carrying case for TAD antennas
    $350.00
          

NEW Product from Hi-Q-Antennas,

The Innovators!

Announcing the "EB" (Egg Beater) CapHat!

Due to its LARGE Capture Area In comparison to a 3' long whip installed on the Hi-Q-5/80 RT antenna the following IMPROOVEMENT was measured on the HP VNA.

Please note that the 3' whip length is chosen to  maintain the overall Hi-Q- Antenna height of 6'.

When an other 3' whop was installed on the TOP of the

EB-8 CapHat, then having an overall antenna height would be 9' and further improvement is realized.

This method of adding whip length to the top of the EB-4 or EB-8 to achieve the 13'6" limit great improvement can be measured.

So what will it buy for ANY HF mobile antenna?

You can "SEE" the difference by setting the resonance to a given low band frequency, example; 3.900 kc, count the NUMBER of turns of the EXPOSED (active) TURNS with your existing whip length. Then install an EB-4 or EB-8 and count again the EXPOSED TURNS!

WOW! MANY turn less at the SAME frequency resonance.

Which then translates to LESS coil wire resistance and GREATER RE, (Radiation Efficiency).

• EB-4
  $75.00
  

Plus S&H of $7.50

This is all great! But while you are trying to improve your OLD CONTRAPTION by the Brand X makers, why not go for the GOLD Standard:

A Hi-Q-HF Mobile antenna!

73, from the Innovators!

Patent Pending.

Brand NEW Shakespeare Style 4245-1 Rigidized Spring Mount with installation kit. The 1" diameter 5" long Sliding Tenon has 8 TPI threads on which the NEW Ruggedized Hi-Q-5/80 or -5/160 HF antenna slides on, then screws on firmly. The Tenon may be in ENGADED or Dis-engaged position, that is: it may be fully springy or fixed. The Spring is wound with 3/8" diameter spring steel wire. The base is INSULATED and ANY antenna may be mounted to it. NOS.

This is NEW! A SIMPLE DPDT UP-DOWN Hi-Q Antenna controller.

$35.00 website link for ordering to follow soon!

New!!

Stainless steel whips:

8' Tapered Stainless Steel whips, whip only $20.00

8' Whip with Hi-Q Whip base, adjustable $30.00

8' Whip with Hi-Q Whip base and installed Hi-Q Corona Ball $35.00

8' Whip and single Lobe CapHat $45.00

S&H $10.00

Questions?

You may get the answers you are looking for by reading the Hi-Q-Antennas™Installation Notes. This document is in Adobe PDF format. Or you can contact me directly with your questions.

Copyright 2003, All Rights Reserved.   "Hi-Q-Antennas" is the registered Trademark of Charles M. Gyenes

Hi-Q-Antennas reserves the rights to make changes in DESIGN, Material and
function of ALL of the Hi-Q products

Web Site Design and Hosting by QTH.COM